Plifold
← Papercraft

Dragon papercraft template

Make a winged dragon in folded cardstock. Dry-fit the zigzag trailing edge of the raised wing. Seat each inward corner before pressing the adjacent finger, and check that the two feet touch the same straightedge.

Finished size (W × H × D)
93 × 57 × 18 mm
Difficulty
Intermediate
Cardstock
160–200 gsm
Assembled winged dragon shown as a digital model.
Digital assembly view. The PDF includes plain face plates for your own finish.

Dragon papercraft template materials and scoring

Step by step

  1. Print the plates and bands. Choose A4 or US Letter, print both sheets at actual size and measure the 25 mm bar. Plate A is the front and B is its mirror. Cut both outer contours, leaving the numbered edge map intact.
  2. Prepare the numbered strips. The 3 strips form 42 wall panels. Score every dashed line while the sheet is flat, then cut the solid outline around each strip, keeping the two rows of tabs and the end flap. Edge 36 is the shortest at 3.2 mm. Pinch that crease against the ruler.
  3. Fit the front profile. Dry-fit the zigzag trailing edge of the raised wing. Seat each inward corner before pressing the adjacent finger, and check that the two feet touch the same straightedge. With the printed strip numbers facing inside, match panel 1 to edge 1 on the map. Glue one row of tabs to the inside of A, working around the numbered outline. Join the end flaps behind the next strip.
  4. Close the back. Use plate B to check the fit before adding glue. Fold the free row of tabs inward and attach B in short sections. Check that the finished piece is 18 mm deep at both ends. Add drawn details to the face if desired.

Planning the winged dragon build

The finished piece measures 93 mm across and 57 mm high when you look squarely at the front. The side wall adds 18 mm of depth. Lay a strip beside the wing on the numbered map. Alternate the direction of the bends at the notches between the wing fingers. Rest the two flat soles on a ruler while the tabs under the feet set.

Allow about 70–90 minutes of hands-on work as a planning estimate, plus drying time for your glue. There are 42 numbered wall panels to bend. If you are new to cutting models, begin with the front and leave the side strips for a second sitting. Keep the edge map on the table between sessions so you can find your place again.

Reading the edge map and checking the fit

7–10 17–21 31 37
Bend panels 7–10 around the notches under the wing. Panels 17–21 climb over the two horns. Set edges 31 and 37 on the same straightedge while the first row of foot tabs sets.

For this outline the bands cover edges 1–15, 16–34, 35–42, in that order. Together they travel approximately 394 mm around one face. Separate the bands one at a time. Write their first and last numbers on scrap slips and lay the strips beside them. A slipped strip can look almost right until you reach a corner that bends the opposite way.

Edge 13, about 27.9 mm long, is a useful straight reference. Lay that panel against the matching line with no glue and hold both ends level. Then try edge 36, only 3.2 mm. If that corner springs open, deepen the score on the waste side of a test strip and try the same pressure on the real hinge.

Finishing the winged dragon and correcting a twisted seam

Draw the wing ribs on the loose face. Start each line at the shoulder and end it at a different wing finger. Leave the narrow horn tips clear of ink and check the feet against the table before closing the back.

Place the unglued back over the standing walls and sight along the long reference edge. If one end lifts, trace the numbers back to the last joint that sits flush. Check the band order and fold direction there before pressing the back down. Allow the adhesive to grab with both plates parallel. A control print and digital assembly view are available here. A learner build with paper is still pending.

Related projects

Papercraft mask template →Compare 3D model constructions