Plifold
← Papercraft

Winter candle papercraft template

Make a winter candle in folded cardstock. Set the flame and the irregular wax rim before forming the broad candle body. The saucer closes last.

Finished size (W × H × D)
56 × 59 × 21 mm
Difficulty
Easy with careful scoring
Cardstock
160–200 gsm
Assembled winter candle shown as a digital model.
Digital assembly view. The PDF includes plain face plates for your own finish.

Winter candle papercraft template materials and scoring

Step by step

  1. Print the plates and bands. Choose A4 or US Letter, print both sheets at actual size and measure the 25 mm bar. Plate A is the front and B is its mirror. Cut both outer contours, leaving the numbered edge map intact.
  2. Prepare the numbered strips. The 2 strips form 17 wall panels. Score every dashed line while the sheet is flat, then cut the solid outline around each strip, keeping the two rows of tabs and the end flap. Edge 6 is the shortest at 5.8 mm. Pinch that crease against the ruler.
  3. Fit the front profile. Set the flame and the irregular wax rim before forming the broad candle body. The saucer closes last. With the printed strip numbers facing inside, match panel 1 to edge 1 on the map. Glue one row of tabs to the inside of A, working around the numbered outline. Join the end flaps behind the next strip.
  4. Close the back. Use plate B to check the fit before adding glue. Fold the free row of tabs inward and attach B in short sections. Check that the finished piece is 21 mm deep at both ends. Add drawn details to the face if desired.

Planning the winter candle build

The finished piece measures 56 mm across and 59 mm high when you look squarely at the front. The side wall adds 21 mm of depth. Decide which face will point toward the room. Mark its back lightly in pencil and plan any decoration while the plate is loose. For a table display, put the unglued front over a scrap base to check which points would touch the surface.

Allow about 40–60 minutes of hands-on work as a planning estimate, plus drying time for your glue. There are 17 numbered wall panels to bend. If you are new to cutting models, begin with the front and leave the side strips for a second sitting. Keep the edge map on the table between sessions so you can find your place again.

Reading the edge map and checking the fit

Choose the file that matches the paper loaded in your printer. Both editions give the same finished dimensions. If the scale bar is short, turn off fit-to-page and print again before cutting anything. For a colour finish, test a pencil or marker on the unused margin. Some markers bleed through card and can hide the scoring marks on the other side.

For this outline the bands cover edges 1–14, 15–17, in that order. Together they travel approximately 222 mm around one face. Separate the bands one at a time. Write their first and last numbers on scrap slips and lay the strips beside them. A slipped strip can look almost right until you reach a corner that bends the opposite way.

Edge 16, about 52.0 mm long, is a useful straight reference. Lay that panel against the matching line with no glue and hold both ends level. Then try edge 6, only 5.8 mm. If that corner springs open, deepen the score on the waste side of a test strip and try the same pressure on the real hinge.

Finishing the winter candle and correcting a twisted seam

Use a warm colour for the flame and a lighter field for the wax. Draw any wick detail before assembly to avoid pressing on the narrow top.

Place the unglued back over the standing walls and sight along the long reference edge. If one end lifts, trace the numbers back to the last joint that sits flush. Check the band order and fold direction there before pressing the back down. Allow the adhesive to grab with both plates parallel. A control print and digital assembly view are available here. A learner build with paper is still pending.

Related projects

Paper snowflake template for a six-point cutout →Harvest pumpkin papercraft template →Compare 3D model constructions