Hold down the bottom section (marked “Hold still” in the picture) and fold the rest up together.
Where it goes
The two slanted creases fold up and the horizontal one folds down: bring the left, right and top corners all down onto the bottom corner, then press flat.
Hand by hand
With one hand, hold down the bottom section (either side of the lower half of the vertical crease); it stays flat throughout.
With the other hand, take the left and right corners and raise them up and inwards along the two slanted creases.
Push the top corner down along the horizontal crease; the left and right sections fold into the middle with it.
Line the left, right and top corners up on the bottom corner, then press flat.
Check
You have a small diamond pointing up, with all four corners at the bottom point: one flap at the front, one at the back, and one tucked inside each side.
Watch out
If it won't collapse, a crease is usually going the wrong way: the slanted creases should rise towards you and the horizontal one should sink away.
Step 11 Fold the lower right edge to the centre line
What to hold
Pick up the right half of the top flap only. Its right edge is a fold joined to the layer underneath, so a little of that layer comes along too; that's normal.
Where it goes
Line the lower right edge up on the vertical centre line, with the crease running from the bottom point up to the upper right edge, then press flat.
Check
A long, narrow triangle appears on the right, its edge along the centre line.
Watch out
Fold only the top flap; keep the bottom point sharp and don't fold it crooked.
Hold the bottom point of the top flap (that flap only); everything above the horizontal crease stays flat.
Where it goes
Lift the bottom point up along the horizontal crease while both sides fold in along the kite creases, then flatten into a long, narrow diamond.
Hand by hand
Hold down the part above the horizontal crease with one hand; with the other, take only the bottom point of the top flap.
Lift the bottom point up along the horizontal crease, like opening a shallow pocket.
Let both sides fold in along the kite creases until their edges reach the centre line.
Bring the bottom point all the way to the top and flatten into a long, narrow diamond.
Check
The front is now a long, narrow diamond whose top point rises above the old top; the small triangles at the lower sides have come in to the centre line.
Watch out
Lift only the top flap; the sides fold in along the creases you already made, so don't force new creases.
Step 19 Fold the lower right edge to the centre line
What to hold
Pick up the right half of the top flap only. Its right edge is a fold joined to the layer underneath, so a little of that layer comes along too; that's normal.
Where it goes
Line the lower right edge up on the vertical centre line, with the crease running from the bottom point up to the upper right edge, then press flat.
Check
A long, narrow triangle appears on the right, its edge along the centre line.
Watch out
Fold only the top flap; keep the bottom point sharp and don't fold it crooked.
Pick up the point at the top of the kite on this side (the top flap and the inner layer joined to it), not the long point at the very top, which is the other side's petal.
Where it goes
Fold the top point down over the kite along the line joining the tops of the two narrow triangles, and crease firmly.
Check
The top point is folded down, covering the tops of the two narrow triangles.
Watch out
The crease should run exactly through the top corners of the two narrow triangles.
Hold the bottom point of the top flap (that flap only); everything above the horizontal crease stays flat.
Where it goes
Lift the bottom point up along the horizontal crease while both sides fold in along the kite creases, then flatten into a long, narrow diamond.
Hand by hand
Hold down the part above the horizontal crease with one hand; with the other, take only the bottom point of the top flap.
Lift the bottom point up along the horizontal crease, like opening a shallow pocket.
Let both sides fold in along the kite creases until their edges reach the centre line.
Bring the bottom point all the way to the top and flatten into a long, narrow diamond.
Check
The front is now a long, narrow diamond whose top point rises above the old top; the small triangles at the lower sides have come in to the centre line.
Watch out
Lift only the top flap; the sides fold in along the creases you already made, so don't force new creases.